DISCBINE® CENTER-PIVOT DISC MOWER CONDITIONERS

CLOSER CUTTING, FASTER DRYDOWN, INCREASED DURABILITY

MODELS

Discbine® 313 (roll)

Cutting width (m)4.00
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261


Standard  Optional 
Discbine® 313 (roll)
MowMax II Cutterbar with ShockPRO hubs
Cutting width (m)4.00
Cutting height (mm)19-70
Cutting height w/opt. high-stubble shoes (mm)76-140
Cutting height w/opt. Biomass shoes (mm)127-198
Cutting height w/opt. adjustable shoes (mm)19-146
Cutterbar tilt angle degrees2-10
Type cutterbarModular
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeChevron intermeshing moulded rubber, or chevron intermessing steel rollers
Length (mm)3175
Diameter (mm)2 x 264 rolls
Conditioner drive method4 HB v-belt & enclosed gears
Speed (rpm)750 or 640
Conditioning roll tension adjustmentSingle crank
Conditioner gap adjustmentDrawbolt stop, each end
Swath width (m)3.00
Windrow width (m)0.9 to 2.4
Driveline
Input speed (rpm)1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required (kW)68
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required - bar103
Electrical7-pin electrical connector for transport lights
Drawbar/2-pt HitchASAE Cat. II or III drawbar or Cat. III 2-pt hitch
Tyres
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum - kph32
Dimensions and Weight
Width, transport (m)4.04
Width, operating (m)6.5 w/2-pt swivel hitch; 6.0 w/drawbar swivel hitch
Length, transport (m)8.4 w/2-pt swivel hitch; 8.1 w/drawbar swivel hitch
Length, operating (m)7.0 w/2-pt swivel hitch; 6.7 w/drawbar swivel hitch
Height, transport (m)2.26
Height, operating (m)2.01
Ground clearance w/header fully raised (mm)411
Weight, Shipping (kg)w/ 2 pt swivel hitch or drawbar 2991
Weight, Operating (kg)w/ 2 pt swivel hitch or drawbar 2846

Discbine® 313 (flail)

Cutting width (m)4.00
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261


Standard  Optional 
Discbine® 313 (flail)
MowMax II Cutterbar with ShockPRO hubs
Cutting width (m)4.00
Cutting height (mm)19-70
Cutting height w/opt. high-stubble shoes (mm)76-140
Cutting height w/opt. Biomass shoes (mm)127-198
Cutting height w/opt. adjustable shoes (mm)19-146
Cutterbar tilt angle degrees2-10
Type cutterbarModular
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeFlail rotor with 120 tapered flails
Length (mm)3175
Diameter (mm)1 x 560 flail rotor
Conditioner drive method4 HB v-belt
Speed (rpm)1042 std. 752 opt.
Conditioning roll tension adjustment
Conditioner gap adjustmentSingle crank adjustment of rotor hood
Swath width (m)3.00
Windrow width (m)0.9 to 2.4
Driveline
Input speed (rpm)1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required (kW)68
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required - bar103
Electrical7-pin electrical connector for transport lights
Drawbar/2-pt HitchASAE Cat. II or III drawbar or Cat. III 2-pt hitch
Tyres
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum - kph32
Dimensions and Weight
Width, transport (m)4.04
Width, operating (m)6.5 w/2-pt swivel hitch; 6.0 w/drawbar swivel hitch
Length, transport (m)8.4 w/2-pt swivel hitch; 8.1 w/drawbar swivel hitch
Length, operating (m)7.0 w/2-pt swivel hitch; 6.7 w/drawbar swivel hitch
Height, transport (m)2.26
Height, operating (m)2.01
Ground clearance w/header fully raised (mm)411
Weight, Shipping (kg)w/ 2 pt swivel hitch or drawbar 2991
Weight, Operating (kg)w/ 2 pt swivel hitch or drawbar 2846

Discbine® 316 (roll)

Cutting width (m)4.95
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261


Standard  Optional 
Discbine® 316 (roll)
MowMax II Cutterbar with ShockPRO hubs
Cutting width (m)4.95
Cutting height (mm)19-70
Cutting height w/opt. high-stubble shoes (mm)76-140
Cutting height w/opt. Biomass shoes (mm)127-198
Cutting height w/opt. adjustable shoes (mm)19-146
Cutterbar tilt angle degrees2-10
Type cutterbarModular
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeChevron intermeshing moulded rubber, or chevron intermessing steel rollers
Length (mm)3175
Diameter (mm)2 x 264 rolls
Conditioner drive method4 HB v-belt & enclosed gears
Speed (rpm)750 or 640
Conditioning roll tension adjustmentSingle crank
Conditioner gap adjustmentDrawbolt stop, each end
Swath width (m)3.00
Windrow width (m)0.9 to 2.4
Driveline
Input speed (rpm)1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required (kW)75
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required - bar103
Electrical7-pin electrical connector for transport lights
Drawbar/2-pt HitchASAE Cat. III drawbar or Cat. III 2-pt hitch
Tyres
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum - kph32
Dimensions and Weight
Width, transport (m)5.05
Width, operating (m)7.8 w/2-pt swivel hitch; 7.3 w/drawbar swivel hitch
Length, transport (m)9.7 w/2-pt swivel hitch; 9.4 w/drawbar swivel hitch
Length, operating (m)8.1 w/2-pt swivel hitch; 7.8 w/drawbar swivel hitch
Height, transport (m)2.26
Height, operating (m)2.01
Ground clearance w/header fully raised (mm)411
Weight, Shipping (kg)w/ 2 pt swivel hitch or drawbar 3184
Weight, Operating (kg)w/ 2 pt swivel hitch or drawbar 3039

Discbine® 316 (flail)

Cutting width (m)4.95
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261


Standard  Optional 
Discbine® 316 (flail)
MowMax II Cutterbar with ShockPRO hubs
Cutting width (m)4.95
Cutting height (mm)19-70
Cutting height w/opt. high-stubble shoes (mm)76-140
Cutting height w/opt. Biomass shoes (mm)127-198
Cutting height w/opt. adjustable shoes (mm)19-146
Cutterbar tilt angle degrees2-10
Type cutterbarModular
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed (rpm)2250
Knife tip speed @ 1000 rpm PTO speed (kph)261
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeFlail rotor with 120 tapered flails
Length (mm)3175
Diameter (mm)1 x 560 flail rotor
Conditioner drive method4 HB v-belt
Speed (rpm)1042 std. 752 opt.
Conditioning roll tension adjustment
Conditioner gap adjustmentSingle crank adjustment of rotor hood
Swath width (m)3.00
Windrow width (m)0.9 to 2.4
Driveline
Input speed (rpm)1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required (kW)75
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required - bar103
Electrical7-pin electrical connector for transport lights
Drawbar/2-pt HitchASAE Cat. III drawbar or Cat. III 2-pt hitch
Tyres
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum - kph32
Dimensions and Weight
Width, transport (m)5.05
Width, operating (m)7.8 w/2-pt swivel hitch; 7.3 w/drawbar swivel hitch
Length, transport (m)9.7 w/2-pt swivel hitch; 9.4 w/drawbar swivel hitch
Length, operating (m)8.1 w/2-pt swivel hitch; 7.8 w/drawbar swivel hitch
Height, transport (m)2.26
Height, operating (m)2.01
Ground clearance w/header fully raised (mm)411
Weight, Shipping (kg)w/ 2 pt swivel hitch or drawbar 3184
Weight, Operating (kg)w/ 2 pt swivel hitch or drawbar 3039
social stream


New Holland Agriculture © 2017
back to top