DISCBINE® CENTER-PIVOT DISC MOWER-CONDITIONERS

CLOSER CUTTING, FASTER DRYDOWN, INCREASED DURABILITY

Gallery

Models

313 (roll)

Cutting width ft. in. (m)13' 0" (4.0)
Number of discs/knives per disc8/2
TypeChevron intermeshing molded rubber, or chevron intermeshing steel rolls
Minimum PTO power required hp (kW)90 (67)


Standard  Optional 
313 (roll)
MowMax II Cutterbar with ShockPRO hubs
Cutting width ft. in. (m)13' 0" (4.0)
Cutting height in. (mm)0.79 - 2.7 (20 - 69)
Cutting height w/opt. high-stubble shoes in. (mm)3.1-5.5 (79-140)
Cutting height w/opt. Biomass shoes in. (mm)4.9-7.8 (124-198)
Cutting height w/opt. adjustable shoes in. (mm)0.79-5.8 (20-147)
Cutterbar tilt angle degrees2 - 10
Type cutterbarModular
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed rpm2250
Knife tip speed @ 1000 rpm PTO speed mph (k/h)162 (261)
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeChevron intermeshing molded rubber, or chevron intermeshing steel rolls
Length in. (mm)125 (3175)
Diameter in. (mm)2 x 10.4 (264) rolls
Conditioner drive method4 HB v-belt & enclosed gears
Speed rpm750 or 640
Conditioning roll tension adjustmentSingle crank
Conditioner gap adjustmentDrawbolt stop, each end
Swath width ft. (m)10 (3.0)
Windrow width ft. (m)3 - 8 (.9 - 2.4)
Driveline
Input speed rpm1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required hp (kW)90 (67)
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required, psi (bar)1500 (103)
Electrical7-pin electrical connector for transport lights
Drawbar/3-pt HitchASAE Cat. II or III drawbar or Cat. III 3-pt hitch
Tires
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum
Transport Speed, Maximum mph20 (32)
Dimensions 1 and Weight 2
Width, transport ft. in. (m)13' 4" (4.04)
Width, operating ft. in. (m)21' 3" (6.5) w/2-pt swivel hitch; 19' 7" (6.0) w/drawbar swivel hitch
Length, transport ft. in. (m)27' 5" (8.4) w/2-pt swivel hitch; 26' 5" (8.1) w/drawbar swivel hitch
Length, operating ft. in. (m)23' 0" (7.0) w/2-pt swivel hitch; 22' 0" (6.7) w/drawbar swivel hitch
Height, transport ft. in. (m)7' 5" (2.26)
Height, operating ft. in. (m)6' 7" (2.01)
Ground clearance w/header fully raised in. (mm)16.2 (411)
Weight, Shipping lb. (kg)Less Hitch 6420 (2912); w/2pt or dbr 6595 (2991)
Weight, Operating lb. (kg)w/2pt or dbr 6275 (2846)

313 (flail)

Cutting width ft. in. (m)13' 0" (4.0)
Number of discs/knives per disc8/2
TypeFlail Rotor w/120 tapered flails
Minimum PTO power required hp (kW)90 (67)


Standard  Optional 
313 (flail)
MowMax II Cutterbar with ShockPRO hubs
Cutting width ft. in. (m)13' 0" (4.0)
Cutting height in. (mm)0.79 - 2.7 (20 - 69)
Cutting height w/opt. high-stubble shoes in. (mm)3.1-5.5 (79-140)
Cutting height w/opt. Biomass shoes in. (mm)4.9-7.8 (124-198)
Cutting height w/opt. adjustable shoes in. (mm)0.79-5.8 (20-147)
Cutterbar tilt angle degrees2 - 10
Type cutterbarModular
Number of discs/knives per disc8/2
Disc speed @ 1000 rpm PTO speed rpm2250
Knife tip speed @ 1000 rpm PTO speed mph (k/h)162 (261)
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeFlail Rotor w/120 tapered flails
Length in. (mm)125 (3175)
Diameter in. (mm)1 x 22 (560) flail rotor
Conditioner drive method4 HB v-belt
Speed rpm1042 std. 752 opt.
Conditioning roll tension adjustmentNA
Conditioner gap adjustmentSingle crank adjustment of rotor hood
Swath width ft. (m)10 (3.0)
Windrow width ft. (m)3 - 8 (.9 - 2.4)
Driveline
Input speed rpm1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required hp (kW)90 (67)
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required, psi (bar)1500 (103)
Electrical7-pin electrical connector for transport lights
Drawbar/3-pt HitchASAE Cat. II or III drawbar or Cat. III 3-pt hitch
Tires
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum
Transport Speed, Maximum mph20 (32)
Dimensions 1 and Weight 2
Width, transport ft. in. (m)13' 4" (4.04)
Width, operating ft. in. (m)21' 3" (6.5) w/2-pt swivel hitch; 19' 7" (6.0) w/drawbar swivel hitch
Length, transport ft. in. (m)27' 5" (8.4) w/2-pt swivel hitch; 26' 5" (8.1) w/drawbar swivel hitch
Length, operating ft. in. (m)23' 0" (7.0) w/2-pt swivel hitch; 22' 0" (6.7) w/drawbar swivel hitch
Height, transport ft. in. (m)7' 5" (2.26)
Height, operating ft. in. (m)6' 7" (2.01)
Ground clearance w/header fully raised in. (mm)16.2 (411)
Weight, Shipping lb. (kg)Less Hitch 6420 (2912); w/2pt or dbr 6595 (2991)
Weight, Operating lb. (kg)w/2pt or dbr 6275 (2846)

316 (roll)

Cutting width ft. in. (m)16' 3" (4.95)
Number of discs/knives per disc10/2
TypeChevron intermeshing molded rubber, or chevron intermeshing steel rolls
Minimum PTO power required hp (kW)100 (75)


Standard  Optional 
316 (roll)
MowMax II Cutterbar with ShockPRO hubs
Cutting width ft. in. (m)16' 3" (4.95)
Cutting height in. (mm)0.79 - 2.7 (20 - 69)
Cutting height w/opt. high-stubble shoes in. (mm)3.1-5.5 (79-140)
Cutting height w/opt. Biomass shoes in. (mm)4.9-7.8 (124-198)
Cutting height w/opt. adjustable shoes in. (mm)0.79-5.8 (20-147)
Cutterbar tilt angle degrees2 - 10
Type cutterbarModular
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed rpm2250
Knife tip speed @ 1000 rpm PTO speed mph (k/h)162 (261)
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeChevron intermeshing molded rubber, or chevron intermeshing steel rolls
Length in. (mm)125 (3175)
Diameter in. (mm)2 x 10.4 (264) rolls
Conditioner drive method4 HB v-belt & enclosed gears
Speed rpm750 or 640
Conditioning roll tension adjustmentSingle crank
Conditioner gap adjustmentDrawbolt stop, each end
Swath width ft. (m)10 (3.0)
Windrow width ft. (m)3 - 8 (.9 - 2.4)
Driveline
Input speed rpm1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required hp (kW)100 (75)
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required, psi (bar)1500 (103)
Electrical7-pin electrical connector for transport lights
Drawbar/3-pt HitchASAE Cat. III drawbar or Cat. III 3-pt hitch
Tires
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum
Transport Speed, Maximum mph20 (32)
Dimensions 1 and Weight 2
Width, transport ft. in. (m)16' 7" (5.05)
Width, operating ft. in. (m)25' 7"(7.8) w/2-pt swivel hitch; 23' 11" (7.3) w/drawbar swivel hitch
Length, transport ft. in. (m)32' 0" (9.7) w/2-pt swivel hitch; 31'' 0" (9.4) w/drawbar swivel hitch
Length, operating ft. in. (m)26' 7" (8.1) w/2-pt swivel hitch; 25' 7" (7.8) w/drawbar swivel hitch
Height, transport ft. in. (m)7' 5" (2.26)
Height, operating ft. in. (m)6' 7" (2.01)
Ground clearance w/header fully raised in. (mm)16.2 (411)
Weight, Shipping lb. (kg)Less Hitch 6845 (3104); w/2pt or dbr 7020 (3184)
Weight, Operating lb. (kg)w/2pt or dbr 6700 (3039)

316 (flail)

Cutting width ft. in. (m)16' 3" (4.95)
Number of discs/knives per disc10/2
TypeFlail Rotor w/120 tapered flails
Minimum PTO power required hp (kW)100 (75)


Standard  Optional 
316 (flail)
MowMax II Cutterbar with ShockPRO hubs
Cutting width ft. in. (m)16' 3" (4.95)
Cutting height in. (mm)0.79 - 2.7 (20 - 69)
Cutting height w/opt. high-stubble shoes in. (mm)3.1-5.5 (79-140)
Cutting height w/opt. Biomass shoes in. (mm)4.9-7.8 (124-198)
Cutting height w/opt. adjustable shoes in. (mm)0.79-5.8 (20-147)
Cutterbar tilt angle degrees2 - 10
Type cutterbarModular
Number of discs/knives per disc10/2
Disc speed @ 1000 rpm PTO speed rpm2250
Knife tip speed @ 1000 rpm PTO speed mph (k/h)162 (261)
Cutterbar flotationVertical and lateral, adjustable springs
Cutterbar drive methodPTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar, replaceable ShockPRO disc drive hubs
Conditioner
TypeFlail Rotor w/120 tapered flails
Length in. (mm)125 (3175)
Diameter in. (mm)1 x 22 (560) flail rotor
Conditioner drive method4 HB v-belt
Speed rpm1042 std. 752 opt.
Conditioning roll tension adjustmentNA
Conditioner gap adjustmentSingle crank adjustment of rotor hood
Swath width ft. (m)10 (3.0)
Windrow width ft. (m)3 - 8 (.9 - 2.4)
Driveline
Input speed rpm1000
Driveline protectionSlip clutch and overrunning clutch assembly @ rear of PTO shaft
Tractor Requirements
Minimum PTO power required hp (kW)100 (75)
PTO shaft spline/size requirements21-spline/1 3/8"
Hydraulic circuits required2
Minimum relief pressure required, psi (bar)1500 (103)
Electrical7-pin electrical connector for transport lights
Drawbar/3-pt HitchASAE Cat. III drawbar or Cat. III 3-pt hitch
Tires
Tubless Ag rib implement tires12.5L x 15 8PR
Transport Speed, Maximum
Transport Speed, Maximum mph20 (32)
Dimensions 1 and Weight 2
Width, transport ft. in. (m)16' 7" (5.05)
Width, operating ft. in. (m)25' 7"(7.8) w/2-pt swivel hitch; 23' 11" (7.3) w/drawbar swivel hitch
Length, transport ft. in. (m)32' 0" (9.7) w/2-pt swivel hitch; 31'' 0" (9.4) w/drawbar swivel hitch
Length, operating ft. in. (m)26' 7" (8.1) w/2-pt swivel hitch; 25' 7" (7.8) w/drawbar swivel hitch
Height, transport ft. in. (m)7' 5" (2.26)
Height, operating ft. in. (m)6' 7" (2.01)
Ground clearance w/header fully raised in. (mm)16.2 (411)
Weight, Shipping lb. (kg)Less Hitch 6845 (3104); w/2pt or dbr 7020 (3184)
Weight, Operating lb. (kg)w/2pt or dbr 6700 (3039)

1 Length and Height- Flail curtain is down for all height and length measurements.
1 Length- windrow shields fully open for length in both transport and operating positions.
1 Length with flail curtain up should be reduced by 2" (50.8mm).
2 Weights shown with rubber conditioning rolls. For weight w/steel conditioning rolls add 100 (45).

social stream

Find a distributor

Search Now

You are at


Let's stay in touch



New Holland Agriculture © 2016
back to top